How to Replace the Replacement Key Battery For the Saab 9-3 Saab owners have to follow a series of special steps to install an additional ignition key. This requires the use of a handheld computer, known as Tech-2 which is used by the dealer. Then it is necessary to purchase a new transponder. key must be purchased. Change your keys regularly to prevent one from deteriorating faster than the next. This will keep your keys in pristine condition. saab 9-5 key As opposed to the traditional Saab keys of the past keys, the new key fobs have electronics inside which makes it hard to duplicate. This has made car theft considerably more complicated than it was 20 years ago. It also makes it more costly to replace keys that were lost. Every owner of a Saab 9-3 should have at least two working keys. If one is lost, it costs a fortune to get another one for the vehicle because it requires replacing the CIM module and programming the locking cylinders. Dealers usually charge between $100-$200 for this. There are some ways around these high cost. Some parts dealers will use the code of an old key to cut a brand new metal blade for a fraction of that of a dealer. The key must be the exact same as the original for it to function in your vehicle. Follow these steps to replace the case. You'll need an flathead screwdriver and patience. With the screwdriver slowly pry the plastic apart and separate the emergency key from the case. After the case is open remove all electronics and place them in the new case. Insert the correct key and badge inside the case. Replacement Battery The Saab 9-3 replacement battery is an inexpensive component that can be quickly and easily replaced. Cyclone's YouTube video Cyd shows how to replace the battery for the remote fob in just four steps. This guide should work with any modern saab-type key fob, though the process may vary slightly. The button is normally located just below the Saab logo on the back of the fob. This is usually located close to the Saab logo on the back of the fob. Use a flathead to insert the screwdriver into the tiny hole on this button. This should be sufficient to let the fob case open so that you can replace the battery. Once the new CR1632 battery is in place, you can reassemble the remote key fob, and then program it to your car. The procedure should take no more than an hour, if not less. This is a simple process that doesn't require any special tools. If you lose a key the procedure will be a bit more involved but it is still able to be done. The dealer will first need to read the VIN of the vehicle, and then purchase an alternative TWICE module, as well as a key blade with the correct unique code. The dealer will then need to program the key using MDI, a brand new software tool. Key Replacement Fob The key fob is the device that locks and unlocks your car. It is equipped with a battery within. They have a limited life span and eventually die. This is a typical issue that occurs with all vehicles, and the good news is that you can change the batteries in a majority of fobs, without replacing the whole case. Amazon sells fobs for replacement that already have all the electronic components installed. You can simply pop the case open and replace the batteries. It is important to note that you'll need to take out the emergency key first. you can do this by inserting the small screwdriver flathead into the slot in the middle of the case. The case should split when you rotate the screwdriver around it. When you are ready to replace your keys, ensure you have a spare, because this can cut down the total cost by a substantial amount. If you have spare keys, you can request that the dealer cut an additional key and program it into your car, which is much cheaper than replacing the whole key fob. If you don't have a spare, it is possible to add a second key to your car, however this requires a lot of research and effort. The cost for adding a second key is several hundred dollars and it also requires programming of the car's computer. Professionals can do this however it's a costly option. Replacement Ignition Contrary to the earlier Saab automobiles, the new SAAB 9-3 models have a much more sophisticated alarm system that is built around a coded key. This means that if you lose your only functioning key, getting an additional one could be extremely expensive as the car has to have a computer module added and it also needs to be specifically designed to accept a different key. Even dealers can charge hundreds of dollars to program a new key in the event that they are unable to complete the task. If you've lost only one working key the dealer will replace your car's computer (known as the CIM or SAAB TWICE) to make an exchange, and they will charge top dollar for it. We can reprogramme the existing EEPROM inside your car's computer so that it's ready for an extra key. This will save you more than 50% on the price you'd pay the dealer. If you have owned a SAAB 9-3 for quite a while you're aware that the ignition keys are not very durable. If your ignition key isn't working correctly, you should look into replacing it. They can become very sticky and the buttons can fall off. It's not as difficult as it seems to replace the ignition key. With the right tools, it is able to be accomplished in a matter of minutes.
saab 9-5 key
